In short: Reading a gear drawing comes down to five numbers. Module or DP, pressure angle, tooth count, bore and face width. Yeh paanch cheezein mil jayein to gear ban jaata hai.
Reading a gear drawing: what it must tell us
A gear drawing is not art. It is a list of sizes we can cut to.
Most drawings that reach us are fine. A few are missing one number, and that one number holds up the quote.
So here is what we look for, in the order we look for it. Read your own drawing along with this and you will know in five minutes whether it is complete.
If something is missing, send what you have anyway. We will ask for the rest.
Module or DP: the first number to find
Module is the size of one tooth. It is the pitch circle diameter divided by the number of teeth.
Indian and European drawings use module, in millimetres. Common values are 2, 3, 4, 5, 6, 8 and 10.
American and British drawings use DP, short for diametral pitch. DP works the other way round. A bigger DP means a smaller tooth.
To swap between them, divide 25.4 by one to get the other. DP 6 is roughly module 4.23.
If the drawing gives neither, measure the old gear. Divide the outside diameter by the tooth count plus two. That gives you the module, close enough to start.
Module se hi tooth ka size tay hota hai, baaki sab uske hisaab se chalta hai.
Pressure angle: 14.5 or 20 degrees
Pressure angle is the slope of the tooth face. Two values cover nearly every gear.
Twenty degrees is the modern standard. It gives a stronger tooth root and runs well under load.
Fourteen and a half degrees turns up on older machines. If you are replacing one gear in an old drive, match what is already there.
A 20 degree gear will not mesh properly with a 14.5 degree one. The contact sits wrong and the pair gets noisy.
The drawing may also show a profile shift, written as a plus or minus x value. It moves the tooth form in or out a little. Tell us if it is there, because it changes the cutter setting.
Tooth count, pitch circle and centre distance
Tooth count is simple to read off a drawing. It is also simple to count on the old gear.
Pitch circle diameter is module times tooth count. You can work it backwards if the drawing gives the outside diameter instead.
Outside diameter is usually the pitch circle plus two modules. That rule alone solves a lot of half finished drawings.
Centre distance matters when we make a pair. It is half the sum of the two pitch circles. Get it wrong and the teeth either jam or rattle.
Bore, keyway, face width and tolerances
The bore is where the gear sits on the shaft. Give us the finished bore size and the fit you want.
Keyway width and depth go with it. A standard key suits most drives, but check the old part before you assume.
Face width is the thickness across the teeth. It sets how much load the gear can carry.
Then come tolerances. Most industrial work runs happily at DIN 8 to DIN 10. Tight classes cost more and take longer, so ask for them only where the machine needs them.
Tell us the surface finish too, if the drawing calls for ground teeth.
Material goes in the same list. Mild steel, C45, EN8, EN19 or an alloy each behave differently under load, and the grade decides the blank we start from.
Drawing nahin hai? Sample se bhi ban jaata hai
No drawing is not a problem. The worn gear itself carries every number we need.
We measure the outside diameter, count the teeth and work the module back from those two. The bore and keyway we measure directly.
Purana gear replace karna hai? Send the part, or send clear photos with a scale or a vernier beside it.
A photo from the side showing the tooth profile helps most. From that we can tell spur from helical, and read the helix angle.
Quotes go out the same working day either way. Same day quote milta hai, chahe drawing ho ya sample.
Gear job work (labour job)
Have a blank or a casting ready? We cut teeth to your drawing as teeth cutting job work: hobbing, shaping, bevel generation, keyway and spline cutting and grinding. You can see all our gears, or send the drawing straight to our contact page.
FAQ
Module aur DP mein kya farak hai?
Module is a size in millimetres. DP is a count per inch. Divide 25.4 by one to get the other.
Can you make a gear without any drawing?
Yes. Send the old gear or a sample and we take every size off it.
Pressure angle pata nahin hai, phir?
Send the old gear. We check the tooth form here and match it.
What file formats do you accept?
PDF, DWG, DXF or a clear photo of a hand sketch. All of them work.
Kitne din mein milta hai?
Most gears in 1 to 2 days. Bade forged gears ke liye hum baat karke batate hain.
Ek hi piece chahiye, banega?
Yes. Single piece bhi banate hain, aur batch order bhi.
We make gears to drawing across Punjab, Chandigarh, Haryana, Himachal and Delhi NCR, and send them all over India by transport.
Parkash Gears, gear manufacturer in Ludhiana since 1952. MSME (Udyam) registered. Call or WhatsApp Ashok Goyal: +91 9915280866, +91 8146400866. Website: https://parkashgears.com



