Mill Gears for Sugar, Rice and Cement Plants: What They Need

In short: Mill gears are big, slow and heavily loaded. Sugar, rice and cement plants each wear them out in a different way.

https://www.infobel.com/en/india/parkash_gears/ludhiana_west/IN147580651-08146400866/businessdetails.aspxWhat mill gears have in common

Plant drives run slow. Often under twenty turns a minute at the final shaft.

Low speed sounds easy. It is not. Torque goes up as speed comes down.

So the tooth is wide, the module is coarse and the blank is heavy.

The second thing is run time. A mill runs for months without a stop.

Teeth that mesh day and night wear in a steady, even way. Wear shows up as a change in sound long before it shows on a gauge.

The third thing is dirt. Bagasse, husk and cement dust all find their way into the mesh.

Grit acts like a lapping paste. It grinds the tooth face slowly and never stops.

Sugar mills: slow speed, very high torque

A sugar mill crushes cane between heavy rollers. The drive behind it is one of the hardest in any factory.

Speed at the roller is only four to six turns a minute. Torque is enormous.

Double helical gears suit this job. The two helixes cancel the side thrust between them.

That keeps the shaft steady and the bearings cooler. Herringbone garari isi wajah se sugar mill mein chalti hai.

Shock is the real enemy here. A stone or a hard cane bundle lands straight on the teeth.

So the tooth root is kept generous. The steel is chosen for toughness, not for hardness.

There is a longer piece on gears in sugar mills if you want the detail.

Rice and flour mills: lighter load, far more dust

Rice and flour mills are gentler on torque. They are much harder on cleanliness.

Husk powder floats everywhere. It settles on the gear, soaks up the oil and turns into paste.

That paste holds grit against the tooth face. The face polishes first, then it pits.

So the real fix here is a cover and a schedule, not a harder gear.

Spur and helical pairs do most of the work. Sprockets and chain drives handle the elevators and conveyors.

Rice mill waale aksar poora set nahi, sirf ghisa hua pinion badalte hain. That is usually the right call.

This rice and flour mill guide covers the layout in more detail.

Cement plants: girth gears and kiln drives

A cement plant has the largest gears on this list. The girth gear wraps around the kiln or the ball mill.

Diameters run into several metres. The ring is usually made in segments and bolted together.

The pinion driving it is small by comparison. It wears out first, and that is by design.

A pinion is far cheaper to replace than a ring. So it is treated as the sacrificial part.

Alignment decides everything. A ring that runs out of true loads one arc of teeth and leaves the rest idle.

Dust here is abrasive and alkaline. Open gear lubricant has to be sprayed on, not just smeared.

Our note on cement plant and crusher drives goes through the crusher side too.

Steel and tooth cutting for plant work

EN8 is fine for light duty. EN19 is the usual choice for a loaded drive.

EN353 and similar case steels go in where shock is high and the section is small.

We cut teeth from a forged or cast blank. Hobbing covers external gears and sprockets.

Shaping handles internal rings and tight shoulders. Bevel generation covers right angle pairs.

Hardening is a separate trade. When a drawing asks for it, the blank goes out to a specialist house and comes back to our works for the finishing cuts.

Grinding follows only where the drawing calls for a tight profile. Most mill work runs well cut.

Purana gear badalna hai to kya bhejein

Send the broken part if you still have it. It beats any description.

If the part is gone, send four numbers. Outside diameter, bore, face width and tooth count.

Add the module or the DP if you know it. We work it back from the sample at our Ludhiana unit if you do not.

A photo of the gear sitting in the machine helps as well. It shows us how the part is mounted.

Same day quote milta hai once those numbers are in hand.

Gear job work from your drawing or sample

We make new plant gears to drawing, and we also take in teeth cutting job work on blanks you send us.

That covers hobbing, shaping, bevel generation, keyway and spline cutting, and grinding. Single piece bhi, batch order bhi.

The industries we serve page lists the plants we supply. You can also browse all our gears.

We supply across Punjab, Chandigarh, Haryana, Himachal and Delhi NCR, and send gears all over India by transport.

FAQ

Sugar mill ke liye kaunsa gear sahi rehta hai?
Double helical for the main drive. It cancels the side thrust and keeps the shaft steady.

Delivery kitne din mein milti hai?
One to two days for standard sizes. For a large forged gear, baat karke batate hain.

Girth gear ke segment bhi bante hain?
Yes. Large rings are made in segments and bolted up on site.

Do you harden the gear?
Hardening is sent out to a specialist house when the drawing asks for it. We handle the cutting, the finishing and the inspection.

Job work bhi karte ho?
Haan. Send your own blank and we cut the teeth to your drawing.

Parkash Gears
528, Oswal Street, Miller Ganj, Ludhiana, Punjab 141003
Ashok Goyal: +91 9915280866, +91 8146400866
Website: https://parkashgears.com

Leave a Comment

Your email address will not be published. Required fields are marked *

Need Help?
Scroll to Top